Gearbox overhaul - All components in a practical set!
Bearings and shaft seals complete set for Segway PT refreshment
The PT Pro gearbox bearing and seal set consists of high quality bearings and seals, some of which have been specially manufactured for this purpose and meet the highest quality standards.
Suitable for:
Segway Gen2/i2/x2 Segway SE/i2/x2
This offer is aimed at workshop professionals who know their profession and have high demands on quality and reliability. For a gearbox overhaul, reinforcement or refinement you need high technical skills and a lot of experience with the corresponding machines.
Included in the scope of delivery:
1x needle bearing (needle bushing) suitable for the Segway PT transmission, 1x hardened inner ring - This ring runs in the needle bearing (needle bushing), 1x deep groove ball bearing large, 1x oil seal large (oil seal large) with additional dust lip and incl. spring ring lock, 4x deep groove ball bearing small, 1x oil seal small (oil seal small) with additional dust lip and incl. spring ring lock. The set includes the parts to perform a complete revision and replacement of all bearings and seals in a Segway PT transmission.
1 x needle bearing (needle bush)
1 x inner ring hardened
1 x deep groove ball bearing large
1 x shaft sealing ring large (oil seal large)
2 x deep groove ball bearing small without O-rings
2 x deep groove ball bearing small with O-rings
1x shaft seal small (oil seal small)
The kit includes the parts to perform a complete overhaul and replacement of all bearings and seals in a Segway PT transmission.
Please note that you still need special gear oil!
The use of a magnetic oil drain plug is recommended!
Caution: Only qualified personnel should perform this work. Improper execution can cause damage to the gear unit and endanger road safety!
The shaft must first be cut off with an oversize of 8 to 21 µm (bearing fitting ring). The ring may only be pressed onto the shaft with Loctite 648.
PT Pro procures Gear Box Spare Parts such as bearings, sleeves, shim rings according to our optimized composition from the well-known and well-known quality manufacturers NTN, SNR, ISB, TPI. Most of the components are not available on the market. We are therefore glad that we could inspire the manufacturers for this project.
Important warning! Risk of injury!
General:
- When using our products, it is important to follow the instructions for installation and manual and the warnings associated with them.
- Special care must be taken while handling with electricity.
- When driving on the road, always observe the locally valid laws and regulations!
- Ensure that you wear adequate protective clothing
- If the vehicle is damaged, it may not be driven under any circumstances. Danger of injury!
Mounting:
- Always switch off your electric vehicle and disconnect the power cable before carrying out maintenance work or replacing parts or accessories.
- Remove both batteries / accumulators before starting work.
- PT Pro is generally not liable for damage caused by incorrectly installed attachments, wear and spare parts.
- Always read the latest authorized operating and installation instructions before installation
- In order to avoid damage and malfunctions, installation should only be carried out by qualified personnel! Incorrect mounting can lead to death or serious injury.
- To minimize the risk of injury, please read and follow all instructions and warnings in the user documentation
Driving the vehicle:
- Use of the vehicle can become deadly or result in serious injury due to loss of control, collisions and falls.
- To minimize the risk of injury, read and follow all instructions and warnings in the user documentation.
- PT Pro recommends that you always wear a helmet when driving the vehicle.
- When using the vehicle, the current road traffic regulations in the respective country must be observed
- Always store batteries and accumulators in a dry place and at room temperature (10 - 25 degrees)
- Charge batteries only at adequately fused sockets and with charging cables designed for this purpose
- Protect batteries and their connectors from moisture
- Always switch off your electric vehicle and disconnect the power cable before carrying out maintenance work or replacing parts or accessories.
- Remove both batteries / accumulators before starting work
- Do not clean with steam jet or garden hose or drive through deep puddles! Clean with a damp cloth!
Lamps:
- Please always ensure sufficient battery power for the duration of your ride.
- Never look directly into the light source. This can lead to blindness
Rims:
- Important: Risk of crashing:
- Check rims for damage before every ride!
- Rims with out-of-balance or which show knocks, hairline cracks and deformation must be replaced immediately.
- Hairline cracks are difficult to detect, danger of breaking! Hairline cracks are possible, especially after accidents and after riding fast over high edges (high pavement, thick roots etc.). Here you save at the wrong place!
- Regularly check the screw connection of the rims!
- Never use rims as load securing points (lashing strap!). Lateral tension forces can damage the rim.
Helmets:
- Caution: Not suitable for motorcycling!
- Please read the warnings inside the helmet!
- Only wear the helmet while riding. Danger of strangulation due to getting caught on the chinstrap when climbing or playing.
- The helmet can no longer fulfil its protective function after a fall, so replace it after every fall.
- Materials age due to UV radiation and external influences. To ensure optimum protection, safety helmets should always be replaced after approx. 5 years.
Caution:
Electronic components are generally excluded from return, cancellation and conversion, as these are specific individual productions due to the respective programming of the component or customer-specific optimizations. Complaints can only be accepted if the component was installed by a trained PT Pro technician. In case of self-installation, any form of warranty or guarantee expires. We refer here to § 312g paragraph 2 BGB additionally apply: I. Exclusion already before the beginning of the production of the goods II. Exclusion only in case of considerable economic disadvantages for the entrepreneur.
There are no reviews yet.
