FEAL FL200 Folding 200 cm Ramps for Wheelchairs and Mobility Vehicles
The FEAL FL200 ramps are a high-quality portable ramp solution for overcoming suitable height differences and loading wheelchairs and mobility vehicles. The set consists of two individual folding aluminium ramps, each 200 cm long.
The two ramps can be positioned according to the track width of the respective vehicle, making them suitable for applications where two separate wheel tracks are required, including loading suitable balance wheelchairs and mobility vehicles into cars or vans.
FEAL FL200 Low Edge – Designed for Limited Ground Clearance
The FL200 features FEAL's Low Edge design. Its low side profiles are particularly useful for wheelchairs and mobility vehicles with limited ground clearance.
The perforated aluminium surface provides a structured running surface while allowing water to drain through. Combined with its folding construction, the FL200 provides a practical portable ramp solution.
FEAL FL200 Technical Specifications
-
Product: FEAL FL200 Low Edge
-
Set: 2 individual ramps
-
Length per ramp: 2000 mm / 200 cm
-
Folded length: approx. 1010 mm / 101 cm
-
Internal width: 180 mm / 18 cm
-
Weight per ramp: approx. 6 kg
-
Maximum load: 150 kg per ramp
-
Recommended maximum height: 400 mm / 40 cm
-
Material: aluminium
-
Surface: perforated
-
Construction: folding
-
Design: Low Edge with low side profiles
200 cm Loading Ramps for Cars and Vans
A typical application for the FEAL FL200 is loading a suitable wheelchair or mobility vehicle into a car, van or transporter. The folding construction reduces the transport length from 200 cm to approximately 101 cm.
FEAL specifies a recommended maximum height of 40 cm for this ramp length. This does not replace an assessment of the individual application. With the same ramp length, a lower loading height generally results in a lower gradient.
Before purchase, measure the actual loading height and check whether the ramp length, resulting gradient and available space are suitable for the mobility vehicle being loaded.
For Genny Zero, Hoss R1, Series 5 and Segway PT
PT Pro offers the FEAL FL200 for suitable applications with balance wheelchairs and mobility vehicles including:
- Genny Zero balance wheelchair
- Hoss R1 balance wheelchair
- Freedom One Life Series 5
- Segway PT
- suitable seated Segway systems and Personal Transporters
- other suitable wheelchairs and mobility vehicles
Important: Mentioning a vehicle model does not constitute universal approval for every configuration or loading situation. Total weight, weight distribution, track width, tyre width, ground clearance, wheel contact area, gradient and secure ramp support must be checked before use.
Folding Design for Easier Transport
Each FL200 ramp folds for transport and storage, reducing its length to approximately 101 cm. At approximately 6 kg per ramp, the two tracks can be handled individually and stored in a suitable vehicle.
This makes the FL200 particularly useful for users who prefer a portable loading solution rather than a permanently installed vehicle ramp or lift.
For Steps, Thresholds and Height Differences
The FEAL FL200 can also be used to overcome suitable steps, thresholds and other height differences, provided that a sufficiently stable and secure support surface is available.
The manufacturer's recommended maximum height of 40 cm should not be interpreted as universal approval for every 40 cm application. Suitability depends on the wheelchair or mobility vehicle and the specific conditions of use.
Safety When Using the Ramps
Before each use, inspect the ramps, hinges, running surfaces and support areas for damage and correct condition. Damaged ramps must not be used.
- observe the maximum load rating
- position both ramps parallel and according to the vehicle track width
- ensure sufficiently large and stable support surfaces
- secure the ramps against unintended movement
- keep running surfaces free from ice, oil and other slippery contamination
- consider vehicle weight and weight distribution
- check gradient and ground clearance before use
- follow the manufacturer's operating and safety instructions
Manufactured by FEAL AB in Sweden
The FL200 ramps are manufactured by FEAL AB in Sweden. FEAL develops and manufactures portable ramp systems and solutions for wheelchair and mobility applications.
PT Pro supplies the FEAL FL200 as a specialist retailer for innovative mobility, balance wheelchairs and Segway PT based mobility solutions.
Which Ramp Is Suitable for My Wheelchair or Vehicle?
Ramp length is only one factor when selecting a suitable loading solution. Important considerations include loading height, required gradient, vehicle weight, track width, tyre width, ground clearance and available storage space.
When loading balance wheelchairs such as Genny Zero or Hoss R1, the actual combination of mobility device and vehicle should be assessed. PT Pro can assist customers in selecting a suitable portable loading solution based on the relevant dimensions and intended application.
